Synthesis and characterization of Ni-P-CNT's nanocomposite film for MEMS applications
顯示簡易詮釋資料 統計資料| 欄位 | 內容 | 語言 |
|---|---|---|
dc.citation.epage |
547 | en_US |
dc.citation.issue |
5 | en_US |
dc.citation.spage |
539 | en_US |
dc.citation.volume |
4 | en_US |
dc.citation.woscount |
21 | |
dc.contributor.author |
Shen, GR | en_US |
dc.contributor.author |
Cheng, YT | en_US |
dc.contributor.author |
Tsai, LN | en_US |
dc.contributor.department |
機械工程學系 | zh_TW |
dc.contributor.department |
電子工程學系及電子研究所 | zh_TW |
dc.contributor.department |
Department of Mechanical Engineering | en_US |
dc.contributor.department |
Department of Electronics Engineering and Institute of Electronics | en_US |
dc.date.accessioned |
2014-12-08T15:18:30Z | |
dc.date.available |
2014-12-08T15:18:30Z | |
dc.date.issued |
2005-09-01 | en_US |
dc.description.abstract |
An electroless phosphorus nickel-carbon nanotube's (Ni-P-CNT) nanocomposite film synthesis and related process for microelectromechanical systems device fabrication have been successfully developed and presented in this paper. With a special acid oxidative method, a well-dispersed nickel-CNT's colloidal solution has been produced without any aggregation, which is very suitable for microstructure fabrication. The nanoindentation measurement indicates that the Young's modulus and hardness of the Ni-P-CNT's nanocomposite film plated in the bath with 0.028-g/L CNTs can greatly increase up to 665.9 and 28.9 GPa, respectively, which are approximately four times larger than that of pure nickel. Moreover, the content of CNTs in the Ni-P-CNT's films is measured by an elemental analyzer. Via the electrical resistivity measurement using a four-point probe, it is found that the electrical property of the nanocomposite film can be well characterized using a Maxwell-Wagner model for a two-phase mixture. The performance improvements of the electrothermal microactuator made of the nanocomposite, including device strength and power efficiency, have been proven similar to the actuator made of the Ni-diamond composites by electrolytic plating by Tsai et al, but with more efficiency and higher strength than the Ni-diamond device does. | en_US |
dc.identifier.doi |
10.1109/TNANO.2005.851397 | en_US |
dc.identifier.issn |
1536-125X | en_US |
dc.identifier.journal |
IEEE TRANSACTIONS ON NANOTECHNOLOGY | en_US |
dc.identifier.uri |
http://dx.doi.org/10.1109/TNANO.2005.851397 | en_US |
dc.identifier.uri |
https://ir.lib.nycu.edu.tw/handle/11536/13315 | |
dc.identifier.wosnumber |
WOS:000231809500010 | |
dc.language.iso |
en_US | en_US |
dc.subject |
carbon nanotube (CNT) | en_US |
dc.subject |
electroless plating | en_US |
dc.subject |
electrothermal microactuator | en_US |
dc.subject |
nanocomposite | en_US |
dc.subject |
nickel | en_US |
dc.title |
Synthesis and characterization of Ni-P-CNT's nanocomposite film for MEMS applications | en_US |
dc.type |
Article | en_US |
檔案
- 000231809500010.pdf (1.95 MB, Adobe PDF)
所屬典藏: 期刊論文
引用此條目
Shen, G., Cheng, Y., & Tsai, L. (2005). Synthesis and characterization of Ni-P-CNT's nanocomposite film for MEMS applications. IEEE TRANSACTIONS ON NANOTECHNOLOGY, 4(5), 539–547. https://doi.org/10.1109/TNANO.2005.851397
引用文字依 APA 第 7 版格式自動產生,使用前請再核對。
分享
永久網址:https://ir.lib.nycu.edu.tw/handle/11536/13315