Browsing by Author "Chen, I. G."

Now showing 1 - 4 of 4

A Superconducting Magnetization System With Hybrid Superconducting Wire for the Study and Application of Superconductivity
(2012-06-01)
Chen, S. D.
;
Yu, Y. T.
;
Jan, J. C.
;
Lin, F. Y.
;
Hwang, C. S.
For the study of high-temperature superconductors and for the application of superconductivity, a superconducting high-field magnetization system with a hybrid superconducting coil was designed. This coil is composed of superconducting wires of three kinds-HTS YBCO 2G-wire, high-field and low-field NbTi wires. Three principal purposes of building this system are to inspect the characteristics of disk-shape bulk YBCO, to develop a HTS-bulk undulator, and to magnetize a portable HTS-bulk high-field magnet for application to a resonant X-ray scattering experiment. With four steps of temperature decrease, a two-stage GM-type cryocooler and liquid nitrogen provide cooling for the magnetization system. The hybrid superconducting coil, two cryogenic systems for the magnetization system and the portable HTS-bulk magnet, and the control and monitor systems that were designed are discussed.
Design Improvement of a Staggered YBCO Undulator
(2018-04-01)
Chen, S. D.
;
Chiang, C. A.
;
Yang, C. M.
;
Yang, C. K.
;
Luo, H. W.
A strong field and short period undulator can be a desirable light source device in a storage ring or a free-electron laser. Bulk YBCO can be used to construct a high-temperature-superconducting undulator in a staggered array structure. The YBCO material in form of 32 mm diameter and 2.5 mm thick was used to assemble a staggered magnet array. The period length is 5 mm and the magnet gap is 4 mm. To estimate the strength of a sinusoidal field and to optimize the end-pole design to minimize the first (i.e., electron angle) and second field integral (electron position), an energy-minimization method (EM-method) based on Bean's model to simulate the field trapped in the HTS-Block is introduced. In this paper, we focus on promoting the practical value of the EM-method simulation. Combining the experimental experience of a YBCO staggered undulator and the simulation experience based on the EM-method, we address some issues to enhance the efficacy of this undulator design.
Design of a HTS Magnet for Application to Resonant X-Ray Scattering
(2011-06-01)
Chen, S. D.
;
Yu, Y. T.
;
Huang, Z. W.
;
Jan, J. C.
;
Hwang, C. S.
In material research, the characteristics of novel materials vary greatly with the environment. A magnet with a strong field will be developed for an experimental station for resonant X-ray scattering to investigate the magnetic properties of materials. This magnet will be developed with high-temperature superconductor (HTS) bulk YBa(2)Cu(3)O(7) and magnetized with a HTS coil magnet wound with 2G HTS wire. HTS (RE) BCO will be selected to construct the coil of this magnet. Both the bulk and coil magnets will be assembled on the same movable system. The bulk HTS magnet will provide flux density greater than 4 T with a gap 34 mm that can accommodate the sample holder of the experimental station. The bulk magnet will be cooled with cryocoolers to 29 K and the coil magnet to 4.2 K; the coil magnet is separable from the bulk magnet after the field is trapped. We describe the concept of the magnetic-field calculation, the overall design of these magnets, and the cooling algorithm for the bulk HTS magnet system.
Feasibility and Features of a Staggered Undulator Constructed With HTS YBCO Bulks
(2014-06-01)
Chen, S. D.
;
Hwang, C. S.
;
Yang, C. M.
;
Chen, I. G.
;
電子物理學系
A staggered undulator with high-temperature superconducting bulks might be a solution to achieve an undulator with an extremely short period for a synchrotron light source. YBCO bulk was thus selected to investigate the feasibility. This bulk (diameter 32 mm, thickness 2.5 mm) was used to build a staggered-magnet array structure and a mock-up staggered undulator of period 5 mm and fixed gap 4 mm was designed for this test. The potential generation of a sinusoidal field was tested in a 3-T magnetization system with field-cooling magnetization (FCM). The practicability of a HI'S undulator is discussed in regard to the possibility of correction of the local field, repetition of field trapping and long-term stability. In addition, a field simulation concept was developed for designing the staggered undulator with YBCO bulks.