Browsing by Author "Chen, Shi-Wei"

Now showing 1 - 4 of 4

Down Shifted Converssion for Enhanceed HIT SSolar Cell Efficiency
(2017-01-01)
Lin, Albert S.
;
Parashar, Parag
;
Huang, Wei-Ming
;
Huang, Yi-Wen
;
Jian, Ding-Rung
In this work, HIT solar cell is incorporated with the luminescent down-shifting (LDS) mechanism for the incident solar spectrum. The heterojunction with intrinsic thin-layer(HIT) solar cell is highly efficient, low temperature (200 C), low cost, and highly symmetrical device. Nevertheless, the carrier collection efficiency is low for the short wavelength solar photons due to the surface recombination. Here, a thin phosphor layer is spray coated on the top of HIT solar cells for the luminescent down-shifting of high energy photons and thus enhanced external quantum efficiency (EQE) for the device for lambda=300nm-450nm is observed.
Hardening steels by the generation of transient phase using additive manufacturing
(2019-06-01)
Huang, E-Wen
;
Lee, Soo Yeol
;
Jain, Jayant
;
Tong, Yang
;
An, Ke
In the present work, the tensile properties of 15-5 PH steel fabricated by selective laser melting (SLM) were examined with respect to the transient austenite phase. Compared with the 8%-transient-phase sample, the 18%-transient-phase one shows higher ultimate tensile strength and relatively low yield strength, as well as hardening behavior. We conducted in-situ neutron-diffraction study to examine the microstructure evolution for mechanistic understanding. After applying the external load, most non-equilibrium, retained austenite in the 8% transient-phase sample transforms before the yield strength, whereas in the 18%-transient-phase sample only 50% of the austenite transforms. Accompanying with the phase transformation, a decrease in the dislocation density and the dislocation strain energy-assisted phase transformation of the ferrite phase are found in the 8%-transient-phase sample even before yielding, which, however, is not the case in the 18%-transient-phase sample. The study demonstrates the SLM enables tuning the amount of transient-phase ratio and coherency between phases to realize a mechanical property control for additive manufactured steel.
Phase Stress Partition in Gray Cast Iron UsingIn SituNeutron Diffraction Measurements
(1970-01-01)
Tu-Ngoc Lam
;
Wu, Szu-Chien
;
Chae, Hobyung
;
Chen, Shi-Wei
;
Jain, Jayant
Gray cast iron comprises alpha-Fe, Fe3C and graphite with their different anisotropies in terms of structure and mechanical behavior. We perform two different deformation paths as tension-compression and compression-tension on bulk gray iron to capture the stress partitioning. Usingin situneutron diffraction, the composite-like deformation behaviors of alpha-Fe and Fe3C are revealed simultaneously. Within the elastic deformation stage, both deformation paths do not cause load transfer. However, when the applied compressive stress exceeds 300 MPa, there is a clear load sharing in both paths. From microscopic examinations, the debonding between matrix and graphite is clarified.
Plastic anisotropy and deformation-induced phase transformation of additive manufactured stainless steel
(2019-08-05)
Chae, Hobyung
;
Huang, E-Wen
;
Jain, Jayant
;
Wang, Huamiao
;
Woo, Wanchuck
Plastic anisotropy and deformation-induced phase transformation of additively manufactured (AM) stainless steels were investigated via in-situ neutron diffraction, electron backscatter diffraction, metallography, and fractography. Two types of tensile specimens were manufactured: (1) One sample was vertically fabricated with its tensile axis parallel to the z-direction (AM-V), (2) The other sample was horizontally fabricated with its tensile axis perpendicular to the z-direction (AM-H). A commercial 15-5PH stainless steel (CA) was used for comparison. AM steel revealed enhanced yield strength, tensile strength, and uniform elongation over CA, which was mainly due to grain refinement and transformation induced plasticity (TRIP). Different onsets of strain nonlinearity between AM-V and AM-H were closely related to martensitic phase transformation. Stresses estimated from lattice strains measured by neutron diffraction matched well with the applied stress-strain curves. After plastic deformation, voids were formed and congregated near the solidified line where fine grains were populated. Higher dislocation density was observed in the fine grain zone, and lower density was shown in the relatively coarse grain zone. AM steels exhibited significant anisotropic fracture behavior in terms of loading direction. In contrast to isotropic failure for CA and AM-V, AM-H revealed anisotropic failure with elliptical formation of the fracture feature. The fracture surface of AM-H possessed many secondary cracks propagating perpendicular to the building direction. The occurrence of secondary cracks in AM-H resulted in rapid load drop during tensile loading after necking.