Browsing by Author "Jian, Jhong-Ting"

Now showing 1 - 3 of 3

A 0.6 V, 1.66mW Energy Harvester and Audio Driver for Tympanic Membrane Transducer with Wirelessly Optical Signal and Power Transfer
(2014-01-01)
Jian, Jhong-Ting
;
Song, Yu-Lin
;
Lee, Chia-Fone
;
Chou, Yuan-Fang
;
Cheni, Wei-Zen
An energy harvester and ultra-low-voltage audio driver to mechanically stimulate tympanic membrane (TM) transducer is presented. By wirelessly optical signal and power transfer, the audio driver is able to directly drive the actuator on the TM to improve sound quality while avoiding occlusion effects. The measured THD+N is 0.4% over the audio bandwidth with modulation index of 0.4, and maximum power conversion efficiency is 24.7%. The core circuits dissipate 1.66mW from 0.6 V through optical power transfer. Fabricated in TSMC 90 nm CMOS technology, the chip size is 0.88x0.84mm(2).
A 160-GHz Frequency-Translation Phase-Locked Loop With RSSI Assisted Frequency Acquisition
(2014-06-01)
Chen, Wei-Zen
;
Lu, Tai-You
;
Wang, Yan-Ting
;
Jian, Jhong-Ting
;
Yang, Yi-Hung
A 160-GHz frequency-translation PLL with tuning range from 156.4 GHz to 159.2 GHz is presented. Sub-THz 1/9 prescaler is replaced by a 3rd harmonic mixer incorporating a frequency tripler for frequency down conversion. A transformer-based VCO is utilized to alleviate capacitive and resistive load associated with varactor and succeeding buffer stages. Frequency acquisition is assisted by received signal strength indicator (RSSI) for automatic frequency sweeping and fast locking. Fabricated in 65 nm CMOS technology, the chip size is 0.92 mm(2). The PLL locking time is less than 3 mu s. This chip drains 24 mW from a 1.2 V power supply.
The development of a non-surgical direct drive hearing device with a wireless actuator coupled to the tympanic membrane
(2013-12-01)
Song, Yu-Lin
;
Jian, Jhong-Ting
;
Chen, Wei-Zen
;
Shih, Chih-Hua
;
Chou, Yuan-Fang
A non-surgical, direct driving hearing device with an actuator placed on the tympanic membrane was designed, fabricated and tested. The actuator consisted of two photodiodes, an aluminum ring, two neodymium iron permanent magnets, two opposing wound coils, a latex membrane and a Provil Novo (TM) membrane. The transducer coupled to the ear drum-utilizing photodiodes and permanent magnets on the motive components could eliminate the need for electrical connections to the moving components. An optic probe was designed to allow sound and light signals to enter the ear canal. By using opto-electromagnetic coupling, the developed hearing device could transmit information over a distance without using cables. The wireless actuator was achieved by two configurations: in one, two light emitting diodes were used for carrying the input signals, and in the other, the corresponding photodiodes were used for receiving the light signals and generating the currents in the actuator. The wireless actuator was designed to use light to carry energy and transmit the signals; thus, the occlusion effect created by traditional ear molds could be avoided. Finally, the wireless actuator was fabricated and tested with a laser Doppler vibrometer. The actuator showed displacements of vibration between 30-0.2 nm and from 400 Hz to 7 kHz with reduced vibration at higher frequencies. The gain of the actuator with 120 mu A on the umbo displacement was approximately 3-13 dB from 400 to1500 Hz and decreased to 6 dB between 1500 Hz to 3 kHz and down to -1 to -6 dB above 3 kHz. Distortions of the umbo vibration amplitude were approximately -1 to -10 dB across frequencies. The results suggest that light can transmit the sound signal remotely and that adequate amplification can be achieved by this actuator. The reduced amplitude above 3 kHz was a consequence of the mass effect of the actuator, which should be miniaturized in the future. Crown Copyright (c) 2013 Published by Elsevier Ltd. All rights reserved.