Browsing by Author "Lai, Jung-Chin"

Now showing 1 - 5 of 5

A VARIABLE-GAIN TIME AMPLIFIER WITH AUTOMATIC INTERVAL DETECTION
(2015)
Hsiao, Frank
;
Lai, Jung-Chin
;
Hsu, Terng-Yin
;
資訊工程學系
;
Department of Computer Science
This paper presents an all-digital standard cell SR-Latch based time amplifier (TA) with a variable gain of 6X and 12X. In this TA, a two-stage gain selection unit is applied to enable the TA to select either the high gain for short input pulse intervals or the low gain for long input pulse intervals. The time amplification gain is 6 in the input range of -700ps similar to 700ps, and reaches 12 if the input range is -300 similar to 300ps. We present a design that automatically detects the input pulse and switches to the proper TA gain. By applying the proposed TA, a standard cyclic TDC implemented in a UMC CMOS
All-Digital Mismatched Calibrator and Compensator for SR Latch-Based Variable-Gain Time Amplifier
(2020-01-01)
Chao, Kuan-Chieh
;
Lai, Jung-Chin
;
Hsu, Terng-Yin
;
資訊工程學系
;
Department of Computer Science
Two major mismatches in SR latch-based time amplifiers (TA) include input skew, which causes gain imbalance, and loading mismatch, which reduces gain accuracy. Accordingly, we propose an all-digital mismatched self-calibrator and compensator for an SR latch-based variable-gain TA. Tunable matching cells and variable capacitors are built into TAs to compensate for input skew (gain imbalance) and loading mismatch (gain inaccuracy). To ensure that the proposed calibration works efficiently and accurately, the TA must provide at least high and low gains where the low gain calibrates the most significant bit (MSB) and the high gain calibrates the least significant bit (LSB). This self-calibrator costs 4375 gates, and the power consumption is 2.8 mA for the TA gain with 2 and 3.2 mA for the TA gain with 16 at a sampling rate of 10 MHz.
Cost-Effective Time-to-Digital Converter Using Time-Residue Feedback
(2017-06-01)
Lai, Jung-Chin
;
Hsu, Terng-Yin
;
資訊工程學系
;
Department of Computer Science
This paper proposes a time-residue feedback scheme to balance resolution and complexity in a cell-based time-to-digital converter (TDC). The time residue is amplified and fed back into a cyclic-ring Vernier recursively until it cannot be detected correctly. Only one variable-resolution cyclic-ring Vernier and one tunable delay-chain time amplifier (TA) are adopted. Both coarse and fine oscillators of the proposed Vernier which are designed by the same variable-resolution digital controlled oscillator can be switched off to decrease ground bounce during TA activities. With various control codes, the TDC resolution is also programmable. The test application-specified integrated circuit which has a 13-b resolution and occupies 0.02 mm(2) in TSMC 65-nm CMOS process can operate in either feedback or feedforward mode. In feedback mode, the measurements of sampling rate, resolution, input range, differential nonlinearity, and integral nonlinearity are 10 MHz, 0.98 ps, 5.76 ns, +/- 0.8 LSB, and +/- 2.2 LSB, respectively; it also consumes 3 mW at 1 V supply voltage. The sampling rate, resolution, and power dissipation of the feedforward operation are 250 MHz, 6.01 ps, and 17.5 mW, respectively.
Mismatch-Tolerant Time Amplifier with Embedded Self-Calibration
(2015)
Lai, Jung-Chin
;
Hsu, Terng-Yin
;
資訊工程學系
;
Department of Computer Science
This paper presents a reliable self-calibration scheme to reduce the mismatches of SR-Latch based 6X time amplifier (TA) to enhance the resolution of time-to-digital converter (TDC). The proposed calibration is embedded to compensate for process, voltage and temperature (PVT) variations that it can eliminate the gain error caused by input mismatches. With the proposed TA, a standard cyclic TDC implemented in UMC 65-nm CMOS process shows that the resolution is 1.25ps.
The Calibration of Gain error for Time Amplifier Embedded in Time-to-Digital Converter
(2017-01-01)
Lai, Jung-Chin
;
Hsiao, Frank
;
資訊科學與工程研究所
;
Institute of Computer Science and Engineering
This paper presents a methodology of calibration to reduce the linearity error of gain in Time amplifier (TA). We divide the input range to several segments and calculate the average of maximum and minimum TA gain in each segment. We also have the checking points to check the width of input interval and decide which segment and corresponding TA gain is for the measured interval. The checking point is the maximum interval in each segment. The input range for each segment is 50 ps, that is, 0- 50 ps is the first segment, 50- 100 ps is the second segment, and so on. For the TA which the measured range is 700 ps, we divide the range to 14 segments and there is its corresponding TA gain in each segment. The gain error will be reduced from 0.82% to 0.33% and the distortion caused by gain error will be reduced from 5.74 ps to 0.51 ps.