Browsing by Author "Tsai, Y. J."

Now showing 1 - 3 of 3

New observations on the uniaxial and biaxial strain-induced hot carrier and NBTI Reliabilities for 65nm node CMOS devices and beyond
(2006)
Chung, Steve S.
;
Huang, D. C.
;
Tsai, Y. J.
;
Lai, C. S.
;
Tsai, C. H.
In this paper, new observations on the uniaxial and biaxial strain-induced hot carrier reliability and/or NBTI in nMOSFET and pMOSFET respectively have been reported for the first time. Uniaxial and biaxial strained nMOSFET and pMOSFET have been extensively examined. Different mechanisms are responsible for different strains in nMOSFET and pMOSFET. For the nMOFETs, it was found that uniaxial strain device has comparable HC reliability with the control device, while biaxial SiGe-strained device exhibits a much worse reliability. This is related to a large impact ionization rate in a biaxial strain which leads to a much worse reliability. For the pMOSFETs, either uniaxial or biaxial strained device shows a comparable amount of HC degradation, while SiGe S/D strained structure might be better considering process complexity, performance, and reliability Although NBTI is still a great concern in SiGe S/D devices, embedded SiGe S/D technique can improve greatly the device NBTI reliability. These results provide a valuable guideline for the present 65nm and beyond CMOS device design with focus on the strain engineering.
Technology roadmaps on the ballistic transport in strain engineered nanoscale CMOS devices
(2007)
Chung, Steve S.
;
Tsai, Y. J.
;
Tsai, C. H.
;
Liu, P. W.
;
Lin, Y. H.
As device channel length continues to scale beyond 90nm, carrier transport in the ballistic regime becomes critically important. In this paper, the strain engineering and its correlation to the ION current enhancement of CMOS devices in the ballistic regime has been examined. It was characterized by two parameters, the ballistic transport efficiency and the injection velocity. Experimental verifications on very high mobility n- and p-MOSFET channel/substrate orientations with various strains have been made. For nMOSFETs, it shows that uniaxial tensile-stress using CESL is more efficient in current enhancement than the biaxial stress with bulk strained-SiGe technique. For the pMOSFETs, compressive stress using uniaxial or biaxial has been evaluated for various structures. It was found that both ballistic efficiency and the injection velocity can be enhanced in a specific pMOS structure with appropriate combination of CESL and biaxial strain. The technology roadmaps have then been established from advanced 65nm CMOS devices. These results provide a guideline for designing high performance strained technology for CMOS devices in the sub-100nm regime.
The channel backscattering characteristics of sub-100nm CMOS devices with different channel/substrate orientations
(2007)
Tsai, Y. J.
;
Chung, Steve S.
;
Liu, P. W.
;
Tsai, C. H.
;
Lin, Y. H.
The channel backscattering and injection velocity of carriers in advanced CMOS devices are the two key parameters for achieving high drain current enhancement. For the first time, an extensive study of these transport parameters for different substrate orientations has been evaluated for both nMOSFET and pMOSFET. By suitably choosing the substrate orientation, it may achieve a reduced backscattering and an increased injection velocity, which is preferable for designing high performance logic CMOS devices. Results show that, in pMOSFET, (110) substrate is preferred and current enhancement can be greatly enhanced in the < 112 > channel. In comparison, (110) substrate in nMOSFET has an adverse effect in reducing driving current as a result of poorer transport characteristics. Therefore, (100) substrate is expected for nMOSFET design. A guideline is then summarized for the optimum design of high performance CMOS devices.