Browsing by Author "Wang, Huamiao"

Now showing 1 - 3 of 3

Crystal plasticity modeling and neutron diffraction measurements of a magnesium AZ31B plate: Effects of plastic anisotropy and surrounding grains
(2020-02-01)
Wang, Huamiao
;
Lee, Soo Yeol
;
Huang, E-Wen
;
Jain, Jayant
;
Li, Dayong
This study used in-situ neutron diffraction measurements and Elastic ViscoPlastic Self-Consistent polycrystal plasticity model, which incorporates a Twinning and DeTwinning scheme (denoted by EVPSC-TDT), to examine the macro-and micro-mechanical behaviors of a rolled AZ31B plate subjected to uniaxial tension. Three specimens were specifically designed for minimum, maximum and intermediate twinning: (1) loading along the rolling direction, (2) loading along the plate normal, and (3) loading along the direction 45 degrees with respect to the plate normal. Apart from the macroscopic stress strain response, the measured diffraction intensities and internal elastic strains were obtained to examine the activities of the deformation modes at the grain level. The diffraction intensity evolution signaled the volume fraction change of twinning, while the internal elastic strain evolution designated the stress partitioning among the grain orientations. The effect of the surrounding grains on the development of the internal elastic strain was investigated by identifying the corresponding deformation mechanisms. Notably, the corresponding modeling work revealed that the EVPSC-TDT model permitted the prediction of the strain hardening and anisotropic behavior along the directions with minimum, maximum and intermediate twinning at the macroscale, and the evolution of the diffraction intensities and internal strains at the microscale. The results provide a physical understanding of the effects of the load direction, texture and surrounding grains on the role of the deformation modes in hexagonal close-packed polycrystalline materials. (C) 2019 Elsevier Ltd. All rights reserved.
On plastic anisotropy and deformation history-driven anelasticity of an extruded magnesium alloy
(2020-02-01)
Wang, Huai
;
Lee, Soo Yeol
;
Wang, Huamiao
;
Woo, Wanchuck
;
Huang, E-Wen
The plastic anisotropy and unloading anelasticity of an extruded Mg-9 wt.%Al alloy (with two annealed textures) were investigated using in-situ neutron diffraction measurement and crystal plasticity modelling. The distinctive yielding and hardening behaviors during compressive and tensile loading-unloading cycles were interpreted by the alternative operations of different slip/twinning modes. We reveal that the micromechanical responses of differently-oriented grains strongly depend on their neighboring conditions and operative deformation mechanisms. Based on the modelling results, unloading anelasticity is hypothesized to be controlled by the plastic contribution of the hard deformation mode and its impeding effects on easier deformation modes. (C) 2019 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.
Plastic anisotropy and deformation-induced phase transformation of additive manufactured stainless steel
(2019-08-05)
Chae, Hobyung
;
Huang, E-Wen
;
Jain, Jayant
;
Wang, Huamiao
;
Woo, Wanchuck
Plastic anisotropy and deformation-induced phase transformation of additively manufactured (AM) stainless steels were investigated via in-situ neutron diffraction, electron backscatter diffraction, metallography, and fractography. Two types of tensile specimens were manufactured: (1) One sample was vertically fabricated with its tensile axis parallel to the z-direction (AM-V), (2) The other sample was horizontally fabricated with its tensile axis perpendicular to the z-direction (AM-H). A commercial 15-5PH stainless steel (CA) was used for comparison. AM steel revealed enhanced yield strength, tensile strength, and uniform elongation over CA, which was mainly due to grain refinement and transformation induced plasticity (TRIP). Different onsets of strain nonlinearity between AM-V and AM-H were closely related to martensitic phase transformation. Stresses estimated from lattice strains measured by neutron diffraction matched well with the applied stress-strain curves. After plastic deformation, voids were formed and congregated near the solidified line where fine grains were populated. Higher dislocation density was observed in the fine grain zone, and lower density was shown in the relatively coarse grain zone. AM steels exhibited significant anisotropic fracture behavior in terms of loading direction. In contrast to isotropic failure for CA and AM-V, AM-H revealed anisotropic failure with elliptical formation of the fracture feature. The fracture surface of AM-H possessed many secondary cracks propagating perpendicular to the building direction. The occurrence of secondary cracks in AM-H resulted in rapid load drop during tensile loading after necking.