Browsing by Author "Xu, You-Lin"

Now showing 1 - 5 of 5

A characteristic improved technique and analysis with plasma treatment to the electrode on oxide-based resistive random access memory
(2020-03-15)
Lin, Chih-Yang
;
Chang, Ting-Chang
;
Pan, Chih-Hung
;
Chen, Min-Chen
;
Xu, You-Lin
A technique was proposed to concentrate the distribution of set voltages. After a plasma treatment, the stability of the high-resistive state (HRS) increased, and the distribution of set voltages was more concentrated at 0.8 V, with a sufficient HRS/LRS resistive ratio (similar to 100x). In addition, the surface of the TiN electrode became rougher, causing oxygen to enter the TiN electrode and form a TiON layer, which acts as an oxygen reservoir. The reservoir is confirmed and the conduction model is supported by both electrical and material analyses. We propose that the observed improvement is due to the difference in the TiN electrode surface. (C) 2019 Published by Elsevier B.V.
Analyzing Electric Field Effect by Applying an Ultra-Short Time Pulse Condition in Hafnium Oxide-Based RRAM
(2018-08-01)
Wu, Cheng-Hsien
;
Lin, Shih-Kai
;
Pan, Chih-Hung
;
Chen, Po-Hsun
;
Lin, Wen-Yan
In this letter, we determine the importance of the electrical field distribution and strength during the switching process by demonstrating different trends in the degree of reset and the reset pulse time. In general, a longer reset pulse time results in a higher reset energy; a higher reset energy leads to a higher degree of reset, which we obtainedby applying different width square waves. But quite notably, the opposite result was obtained using triangle waves, where a higher degree of reset occurred with a shorter rising time and lower reset energy. We believe that this is due to the electric field effect: if the voltage rises faster than the filament oxidation, the device can produce a larger effective electric field and a higher resistance in the reset process. To further investigate the mechanism, the procedure of the reset process was analyzed in detail, and COMSOL simulation is also carried out for confirmation.
Impact of electrode thermal conductivity on high resistance state level in HfO2-based RRAM
(2020-09-23)
Lin, Shih-Kai
;
Wu, Cheng-Hsien
;
Chen, Min-Chen
;
Chang, Ting-Chang
;
Lien, Chen-Hsin
This study examines the influence of different electrode thermal conductivity on switching behavior during the reset process. Electrical analysis methods and an analysis of current conduction mechanism indicate that better thermal conductivity in the electrode will require larger input power in order to induce more active oxygen ions to take part in the reset process. More active oxygen ions result in a more oxidized switching layer, and cause the effective switching gap (d(sw)) to become larger in the reset process. The effect of the electrode thermal conductivity and input power are explained by our model and clarified by electrical analysis methods.
Overcoming Limited Resistance in 1T1R RRAM Caused by Pinch-Off Voltage During Reset Process
(2019-11-01)
Zheng, Hao-Xuan
;
Chen, Min-Chen
;
Chang, Ting-Chang
;
Su, Yu-Ting
;
Chen, Wen-Chung
This article explains the difference in the reset processes between single RRAM and 1T1R RRAM structures. In the single RRAM, as the reset voltage increases, the off-state resistance increases. This is a normal RRAM operation. However, in the 1T1R structure, the reset voltage increases while the OFF-state resistance does not increase. This may be caused by either current or voltage being insufficient to switch the RRAM to its higher resistance state. The measurements of real voltage indicate that the insufficient voltage is in fact the main cause. For the 1T1R RRAM structure, if it is to be reset to a higher resistance state, it is best done by increasing the gate voltage to increase the OFF-state resistance. Therefore, we provide a method to reduce the misjudgment in the array, and it would be beneficial for the development of high-density memory.
The Effect of Humidity on Reducing Forming Voltage in Conductive-Bridge Random Access Memory With an Alloy Electrode
(2019-10-01)
Lin, Shih-Kai
;
Chen, Min-Chen
;
Chang, Ting-Chang
;
Lien, Chen-Hsin
;
Chang, Jing-Shuen
This letter investigates Au30Ag70 (alloy electrode)/SiO2/TiN conductive-bridge random access memory (CBRAM) to verify the influence of ambient conditions on forming voltage (V-F) and the location of galvanic reaction. Previous literature demonstrates that the galvanic reaction in CBRAM with an alloy electrode results in a lower V-F. In this work, a higher environmental H2O concentration results in a decrease in V-F. From this change in VF, we infer that environmental H2O concentration influences the amount of galvanic reaction. Moreover, we verify the location of the galvanic reaction by varying electrode thickness. Finally, we propose a physical model to explain our observations.