Browsing by Author "Yang, Hao-Yu"

Now showing 1 - 12 of 12

Alternate Hammering Test for Application-Specific DRAMs and an Industrial Case Study
(2012)
Huang, Rei-Fu
;
Yang, Hao-Yu
;
Chao, Mango C. -T.
;
Lin, Shih-Chin
;
電子工程學系及電子研究所
This paper presents a novel memory test algorithm, named alternate hammering test, to detect the pairwise word-line hammering faults for application-specific DRAMs. Unlike previous hammering tests, which require excessively long test time, the alternate hammering test is designed scalable to industrial DRAM arrays by considering the array layout for potential fault sites and the highest DRAM-access frequency in real system applications. The effectiveness and efficiency of the proposed alternate hammering test are validated through the test application to an eDRAM macro embedded in a storage-application SoC.
Detecting Stability Faults in Sub-threshold SRAMs
(2011)
Lin, Chen-Wei
;
Yang, Hao-Yu
;
Huang, Chin-Yuan
;
Chen, Hung-Hsin
;
Chao, Mango C. -T.
Detecting stability faults has been a crucial task and a hot research topic for the testing of conventional super-threshold 6T SRAM in the past. When lowering the supply voltage of SRAM to the subthreshold region, the impact of stability faults may significantly change, and hence the test methods developed in the past for detecting stability faults may no longer be effective. In this paper, we first categorize the subthreshold-SRAM designs into different types according to their bit-cell structures. Based on each type, we then analyze the difference of its stability faults compared to the conventional super-threshold 6T SRAM, and discuss how the stability-fault test methods should be modified accordingly. A series of experiments are conducted to validate the effectiveness of each stability-fault test method for different types of subthreshold-SRAM designs.
Fault Models and Test Methods for Subthreshold SRAMs
(2010)
Lin, Chen-Wei
;
Chen, Hung-Hsin
;
Yang, Hao-Yu
;
Chao, Mango C-T
;
Huang, Rei-Fu
Due to the increasing demand of an extra-low-power system, a great amount of research effort has been spent in the past to develop an effective and economic subthreshold-SRAM design. However, the test methods regarding those newly developed subthreshold-SRAM designs have not yet been fully discussed. In this paper, we first categorize the subthreshold-SRAM designs into three types, study the faulty behavior of different open defects for each type of designs, and then identify the faults which may or may not be covered by a traditional SRAM test method. For those hard-to-detect faults, we will further discuss the corresponding test method according to different each type of subthreshold-SRAM designs. At last, a discussion about the temperature at test will also be provided.
Fault Models and Test Methods for Subthreshold SRAMs
(2013-03-01)
Lin, Chen-Wei
;
Chen, Hung-Hsin
;
Yang, Hao-Yu
;
Huang, Chin-Yuan
;
Chao, Mango C. -T.
Due to the increasing demand of an extra-low-power system, a great amount of research effort has been spent in the past to develop an effective and economic subthreshold SRAM design. However, the test methods regarding those newly developed subthreshold SRAM designs have not yet been fully discussed. In this paper, we first categorize the subthreshold SRAM designs into three types, study the faulty behavior of open defects and address decoders faults on each type of designs, and then identify the faults which may not be covered by a traditional SRAM test method. We will also discuss the impact of open defects and threshold-voltage mismatch on sense amplifiers under subthreshold operations. A discussion about the temperature at test is also provided.
Fault Models for Embedded-DRAM Macros
(2009)
Chao, Mango C. -T.
;
Yang, Hao-Yu
;
Huang, Rei-Fu
;
Lin, Shih-Chin
;
Chin, Ching-Yu
In this paper, we compare embedded-DRAM (eDRAM) testing to both SRAM testing and commodity-DRAM testing, since an eDRAM macro uses DRAM cells with an SRAM interface. We first start from an standard SRAM test algorithm and discuss the faults which are not covered in the SRAM testing but should be considered in the DRAM testing. Then we study the behavior of those faults and the tests which can detect them. Also, we discuss how likely each modeled fault may occur on eDRAMs and commodity DRAMs, respectively.
Predicting Vt Variation and Static IR Drop of Ring Oscillators Using Model-Fitting Techniques
(2017-01-01)
Huang, Tzu-Hsuan
;
Hung, Wei-Tse
;
Yang, Hao-Yu
;
Chang, Wen-Hsiang
;
Chen, Ying-Yen
This paper presents a statistical model-fitting framework to efficiently decompose the impact of device Vt variation and power-network IR drop from the measured ring-oscillator frequencies without adding any extra circuitry to the original ring oscillators. The framework applies Gaussian process regression as its core model-fitting technique and stepwise regression as a preprocess to select significant predictor features. The experiments conducted based on the SPICE simulation of an industrial 28nm technology demonstrate that our framework can simultaneously predict the NMOS Vt, PMOS Vt and static IR drop of the ring oscillators based on their frequencies measured at different external supply voltages. The final resulting R squares of the predicted features are all more than 99.93%.
Random Pattern Generation for Post-Silicon Validation of DDR3 SDRAM
(2015)
Yang, Hao-Yu
;
Kuo, Shih-Hua
;
Huang, Tzu-Hsuan
;
Chen, Chi-Hung
;
Lin, Chris
Due to the demand of pursuing a main memory with larger data bandwidth, higher data density, and lower power, the specification of DRAM has been constantly evolved in the past decade. The new DRAM specifications support multiple operating modes with multiple timing settings. It then becomes computationally infeasible to exhaustively validate all the combinations of different operating modes, timing settings and address/data with pure simulation before silicon. In this paper, we propose a framework to generate proper random patterns for validating a newly designed DDR3 SDRAM based on its first silicon chips. The proposed framework needs to not only guarantee the correctness of the generated patterns according to the state diagram and timing constraints defined in the specification but also provide the flexibility of exploring various design corners for the targeted DDR3 SDRAM. We will also show some successful silicon-validation cases of applying the proposed framework to identify the design errors based on real DDR3 SDRAM products.
Testing Methodology of Embedded DRAMs
(2012-09-01)
Yang, Hao-Yu
;
Chang, Chi-Min
;
Chao, Mango C. -T.
;
Huang, Rei-Fu
;
Lin, Shih-Chin
"The embedded-DRAM(eDRAM) testing mixes up the techniques used for DRAM testing and SRAM testing since an eDRAM core combines DRAM cells with an SRAM interface (the so-called 1T-SRAM architecture). In this paper, we first present our test algorithm for eDRAM testing. A theoretical analysis to the leakage mechanisms of a switch transistor is also provided, based on that we can test the eDRAM at a higher temperature to reduce the total test time and maintain the same retention-fault coverage. Finally, we propose a mathematical model to estimate the defect level caused by wear-out defects under the use of error-correction-code circuitry, which is a special function used in eDRAMs compared to commodity DRAMs. The experimental results are collected based on 1-lot wafers with an 16 Mb eDRAM core."
Testing Methods for a Write-Assist Disturbance-Free Dual-Port SRAM
(2014)
Yang, Hao-Yu
;
Lin, Chen-Wei
;
Huang, Chao-Ying
;
Lu, Ching-Ho
;
Lai, Chen-An
The recent research works of dual-port SRAM have focused on developing new write-assist techniques to suppress the potential inter-port write disturbance under low operating voltage and high process variation. However, the testing related issues induced by those newly proposed write-assist techniques have not been discussed yet in the previous literatures. In this paper, we first implemented a new write-assist dual-port SRAM proposed in [10] by using a 28nm LP process and then discussed the faulty behavior of injecting different resistive-open defects into both the SRAM cell and write-assist circuit. Next, we developed new test methods to detect the hard-to-detect resistive-open defects and proposed a corresponding March-like algorithm that covers a widely used March C-as well as the proposed test methods. Last, the required DfT for the proposed test methods was also discussed.
Testing Methods for Detecting Stuck-open Power Switches in Coarse-Grain MTCMOS Designs
(2010)
Mu, Szu-Pang
;
Wang, Yi-Ming
;
Yang, Hao-Yu
;
Chao, Mango C. -T.
;
Chen, Shi-Hao
Coarse-grain multi-threshold CMOS (MTCMOS) is an effective power-gating technique to reduce IC's leakage power consumption by turning off idle devices with MTCMOS power switches. In this paper, we study the usage of coarse-grain MTCMOS power switches for both logic circuits and SRAMs, and then propose corresponding methods of testing stuck-open power switches for each of them. For logic circuits, a specialized ATPG framework is proposed to generate a longest possible robust test while creating as many effective transitions in the switch-centered region as possible. For SRAMs, a novel test algorithm is proposed to exercise the worst-case power consumption and performance when stuck-open power switches exist. The experimental results based on an industrial MTCMOS technology demonstrate the advantage of our proposed testing methods on detecting stuck-open power switches for both logic circuits and SRAMs, when compared to conventional testing methods.
Testing Methods for Quaternary Content Addressable Memory Using Charge-Sharing Sensing Scheme
(2015)
Yang, Hao-Yu
;
Huang, Rei-Fu
;
Su, Chin-Lung
;
Lin, Kuan-Hong
;
Shu, Hang-Kaung
Due to its capability of parallel search, content addressable memory (CAM) has been widely used on the applications requiring high-speed data search. In recent years, the architectures and design techniques for CAM have been consistently evolving. However, the incoming testing issues for those newly evolved CAM designs are not fully discussed. In this paper, we investigate the testing issues for a new 28nm quaternary CAM, which provides the additional fourth state compared to a conventional ternary CAM and utilizes a charge-sharing sensing scheme for reducing its search power consumption. We first identify the new fault models for this quaternary CAM that are not covered in the conventional CAM testing based on the simulation result, and derive the corresponding test algorithm for those new fault models. The effectiveness of the proposed test algorithm is then validated by the testing result of 7200 28nm sample chips covering different process corners with the help of a newly designed command-based memory BIST.
Testing Strategies for a 9T Sub-threshold SRAM
(2012)
Yang, Hao-Yu
;
Lin, Chen-Wei
;
Chen, Hung-Hsin
;
Chao, Mango C. -T.
;
Tu, Ming-Hsien
Due to the increasing demands of lower-power devices, a lot of research effort has been devoted to develop new SRAM cell designs that can be effectively and economically operated at the subthreshold region. However, each new SRAM cell design has its own cell structure and design techniques, which may result in different faulty behaviors than the conventional 6T SRAMs and require specialized test methods to detect those uncovered fault models. In this paper, we focus on developing the test methods for testing a new 9T subthreshold SRAM design, which utilizes single bit-line read/write, two write word-lines for writing different values, and a separate read path. A mixed march algorithm with different background and address-traverse directions is proposed to detect various uncovered fault models and validated through real test chips. A new specialized technique of floating bit-line attacking is also presented to detect the stability faults, which cannot be effectively detected by applying the conventional test methods, for the new 9T SRAM design.