學術出版;;Publications

Permanent URI for this communityhdl:11536/1

收集所有交通大學研究人員與學生個人或團體所發表之各項學術著作，涵蓋期刊論文、教師專書、學位論文等項。;;Collections of Publications of NCTU Researchers and Students Like Journal Papers and Thesis.

Browse

🏛️國立陽明交通大學機構典藏

Search Results

Now showing 1 - 7 of 7

Chemical mechanical polishing for selective CVD-W
(1997-10-30)
Wang, MT
;
Yeh, WK
;
Tsai, MS
;
Tseng, WT
;
Chang, TC
This work investigates chemical mechanical polishing (CMP) for W-filled contact holes, vias, and trenches by selective chemical vapor deposition. A novel process that combines the CMP technique with selective chemical vapor deposition of tungsten (CVD-W) was employed to remove nail heads due to overgrowth and W-particles on the surface of dielectric due to selectivity loss. The overfilled nail heads and the selectivity loss can be completely removed with very low down-pressure (3 psi) in a very short polishing time (30 s). This indicates that the novel process is very promising for ULSI multilevel interconnection application. The removal rate selectivities of W to thermal oxide, PECVD-TEOS, and BPSG were found to be 47:1, 30:1 and 15:1, respectively, while the selectivities of W to the barrier metals of TiW, Ti and Ta were determined to be 0.6:1, 6:1 and 28:1, respectively. (C) 1997 Elsevier Science S.A.
Chemical mechanical polishing for selective CVD-W
Wang, MT
;
Yeh, WK
;
Tsai, MS
;
Tseng, WT
;
Chang, TC
This work investigates chemical mechanical polishing (CMP) for W-filled contact holes, vias, and trenches by selective chemical vapor deposition. A novel process that combines the CMP technique with selective chemical vapor deposition of tungsten (CVD-W) was employed to remove nail heads due to overgrowth and W-particles on the surface of dielectric due to selectivity loss. The overfilled nail heads and the selectivity loss can be completely removed with very low down-pressure (3 psi) in a very short polishing time (30 s). This indicates that the novel process is very promising for ULSI multilevel interconnection application. The removal rate selectivities of W to thermal oxide, PECVD-TEOS, and BPSG were found to be 47:1, 30:1 and 15:1, respectively, while the selectivities of W to the barrier metals of TiW, Ti and Ta were determined to be 0.6:1, 6:1 and 28:1, respectively. (C) 1997 Elsevier Science S.A.
Chemical mechanical polishing for selective CVD-W
Wang, MT
;
Yeh, WK
;
Tsai, MS
;
Tseng, WT
;
Chang, TC
This work investigates chemical mechanical polishing (CMP) for W-filled contact holes, vias, and trenches by selective chemical vapor deposition. A novel process that combines the CMP technique with selective chemical vapor deposition of tungsten (CVD-W) was employed to remove nail heads due to overgrowth and W-particles on the surface of dielectric due to selectivity loss. The overfilled nail heads and the selectivity loss can be completely removed with very low down-pressure (3 psi) in a very short polishing time (30 s). This indicates that the novel process is very promising for ULSI multilevel interconnection application. The removal rate selectivities of W to thermal oxide, PECVD-TEOS, and BPSG were found to be 47:1, 30:1 and 15:1, respectively, while the selectivities of W to the barrier metals of TiW, Ti and Ta were determined to be 0.6:1, 6:1 and 28:1, respectively. (C) 1997 Elsevier Science S.A.
Nitric acid-based slurry with citric acid as an inhibitor for copper chemical mechanical polishing
(1999-10-15)
Hu, TC
;
Chiu, SY
;
Dai, BT
;
Tsai, MS
;
Tung, IC
A novel inhibitor, citric acid, was introduced in the HNO3-based slurry for copper chemical mechanical polishing. It was anticipated that a passivation layer could be formed on the copper surface in the presence of citric acid. In a 3 vol.% HNO3 solution, the passivation effect derived from citric acid saturated as the citric acid concentration reached ca. 0.01 M. The polishing rate was found to decrease with the addition of citric acid. The results showed that the HNO3-based slurry with citric acid as an inhibitor could achieve good surface planarity for copper chemical mechanical polishing. (C) 1999 Published by Elsevier Science S.A. All rights reserved.
The application of electrochemical metrologies for investigating chemical mechanical polishing of Al with a Ti barrier layer
(2003-11-15)
Chiu, SY
;
Wang, YL
;
Liu, CP
;
Lan, JK
;
Ay, C
In situ electrochemical measurements were performed for Al and Ti disks in various slurries during polishing and static conditions. The electrochemical results obtained from the corrosion potential drop of Al polishing have verified that the maximum removal rate of metal CMP can be achieved when the removal rate of the surface oxide was equal to its growth rate. However, Ti polishing did not exist maximum removal rate. The effects of H2O2%, pH values and pressure on the Al and Ti polishing behaviors were explored by using potentiodynamic scan. The corrosion potential drop was found to be a good index for polishing removal rate. The corrosion potential drop changed with increasing H2O2% for Al polishing and there existed a maximum value. But the corrosion potential drop increased with increasing H2O2% for Ti polishing. The pH value had different effects on Al and Ti polishing. Higher pH values gave higher Al removal rate but lower Ti removal rate. The Al polishing showed more pressure sensitive than Ti polishing did. The galvanic current was measured for AIM polishing. For slurry with 6 vol.% H2O2 and pH = 4, the abraded Al electrode obtained a negative current, which implied Ti oxidation was enhanced. (C) 2003 Elsevier B.V. All rights reserved.
Effects of corrosion environments on the surface finishing of copper chemical mechanical polishing
(1997-10-31)
Wang, MT
;
Tsai, MS
;
Liu, C
;
Tseng, WT
;
Chang, TC
Copper chemical mechanical polishing (Cu-CMP) was investigated using slurries containing alumina abrasive and various types and concentrations of oxidizer, as well as benezotriazole (BTA) additive. We found that the corrosion rate of copper film decreases with increasing BTA concentration in 3 vol.% HNO3 solution, but the passivation effect of BTA saturates as the concentration reaches about 0.01 M. On the other hand, a small amount of H2O2 in H2O2/XJFW8099 slurry enhances the corrosion rate dramatically, while abundance of H2O2 in the slurry suppresses the corrosion reaction effectively. The polishing rate and its non-uniformity decrease with increasing volume ratio of H2O2 in H2O2/XJEW8099 slurry. A very smooth surface with a removal rate of 363.0 nm/min was obtained using the slurry of 1/1 ratio. Depletion of H2O2 in the slurry can result in more abrasive residuals as well as a rougher surface; the surface roughness increases from 0.3 to 9.9 nm as the H2O2/XJFW8099 ratio decreases from 1/1 to 1/4. Our results indicate that the corrosion rate, polishing rate and surface roughness of copper films are sensitively dependent on the type and concentration of oxidizer as well as the BTA additive. (C) 1997 Elsevier Science S.A.
Chemical mechanical polishing for selective CVD-W
(1997-10-30)
Wang, MT
;
Yeh, WK
;
Tsai, MS
;
Tseng, WT
;
Chang, TC
This work investigates chemical mechanical polishing (CMP) for W-filled contact holes, vias, and trenches by selective chemical vapor deposition. A novel process that combines the CMP technique with selective chemical vapor deposition of tungsten (CVD-W) was employed to remove nail heads due to overgrowth and W-particles on the surface of dielectric due to selectivity loss. The overfilled nail heads and the selectivity loss can be completely removed with very low down-pressure (3 psi) in a very short polishing time (30 s). This indicates that the novel process is very promising for ULSI multilevel interconnection application. The removal rate selectivities of W to thermal oxide, PECVD-TEOS, and BPSG were found to be 47:1, 30:1 and 15:1, respectively, while the selectivities of W to the barrier metals of TiW, Ti and Ta were determined to be 0.6:1, 6:1 and 28:1, respectively. (C) 1997 Elsevier Science S.A.

學術出版;;Publications

Browse

Filters

Settings

Sort By

Results per page

🏛️國立陽明交通大學機構典藏

Search Results